mirror of
https://github.com/rene-dev/stmbl.git
synced 2024-12-25 10:02:18 +00:00
710 lines
30 KiB
C
710 lines
30 KiB
C
/**
|
|
******************************************************************************
|
|
* @file stm32f4xx_i2c.h
|
|
* @author MCD Application Team
|
|
* @version V1.6.0
|
|
* @date 10-July-2015
|
|
* @brief This file contains all the functions prototypes for the I2C firmware
|
|
* library.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© COPYRIGHT 2015 STMicroelectronics</center></h2>
|
|
*
|
|
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
|
|
* You may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at:
|
|
*
|
|
* http://www.st.com/software_license_agreement_liberty_v2
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
|
|
/* Define to prevent recursive inclusion -------------------------------------*/
|
|
#ifndef __STM32F4xx_I2C_H
|
|
#define __STM32F4xx_I2C_H
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "stm32f4xx.h"
|
|
|
|
/** @addtogroup STM32F4xx_StdPeriph_Driver
|
|
* @{
|
|
*/
|
|
|
|
/** @addtogroup I2C
|
|
* @{
|
|
*/
|
|
|
|
/* Exported types ------------------------------------------------------------*/
|
|
|
|
/**
|
|
* @brief I2C Init structure definition
|
|
*/
|
|
|
|
typedef struct
|
|
{
|
|
uint32_t I2C_ClockSpeed; /*!< Specifies the clock frequency.
|
|
This parameter must be set to a value lower than 400kHz */
|
|
|
|
uint16_t I2C_Mode; /*!< Specifies the I2C mode.
|
|
This parameter can be a value of @ref I2C_mode */
|
|
|
|
uint16_t I2C_DutyCycle; /*!< Specifies the I2C fast mode duty cycle.
|
|
This parameter can be a value of @ref I2C_duty_cycle_in_fast_mode */
|
|
|
|
uint16_t I2C_OwnAddress1; /*!< Specifies the first device own address.
|
|
This parameter can be a 7-bit or 10-bit address. */
|
|
|
|
uint16_t I2C_Ack; /*!< Enables or disables the acknowledgement.
|
|
This parameter can be a value of @ref I2C_acknowledgement */
|
|
|
|
uint16_t I2C_AcknowledgedAddress; /*!< Specifies if 7-bit or 10-bit address is acknowledged.
|
|
This parameter can be a value of @ref I2C_acknowledged_address */
|
|
}I2C_InitTypeDef;
|
|
|
|
/* Exported constants --------------------------------------------------------*/
|
|
|
|
|
|
/** @defgroup I2C_Exported_Constants
|
|
* @{
|
|
*/
|
|
#define IS_I2C_ALL_PERIPH(PERIPH) (((PERIPH) == I2C1) || \
|
|
((PERIPH) == I2C2) || \
|
|
((PERIPH) == I2C3))
|
|
/** @defgroup I2C_Digital_Filter
|
|
* @{
|
|
*/
|
|
|
|
#define IS_I2C_DIGITAL_FILTER(FILTER) ((FILTER) <= 0x0000000F)
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
|
|
/** @defgroup I2C_mode
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_Mode_I2C ((uint16_t)0x0000)
|
|
#define I2C_Mode_SMBusDevice ((uint16_t)0x0002)
|
|
#define I2C_Mode_SMBusHost ((uint16_t)0x000A)
|
|
#define IS_I2C_MODE(MODE) (((MODE) == I2C_Mode_I2C) || \
|
|
((MODE) == I2C_Mode_SMBusDevice) || \
|
|
((MODE) == I2C_Mode_SMBusHost))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_duty_cycle_in_fast_mode
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_DutyCycle_16_9 ((uint16_t)0x4000) /*!< I2C fast mode Tlow/Thigh = 16/9 */
|
|
#define I2C_DutyCycle_2 ((uint16_t)0xBFFF) /*!< I2C fast mode Tlow/Thigh = 2 */
|
|
#define IS_I2C_DUTY_CYCLE(CYCLE) (((CYCLE) == I2C_DutyCycle_16_9) || \
|
|
((CYCLE) == I2C_DutyCycle_2))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_acknowledgement
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_Ack_Enable ((uint16_t)0x0400)
|
|
#define I2C_Ack_Disable ((uint16_t)0x0000)
|
|
#define IS_I2C_ACK_STATE(STATE) (((STATE) == I2C_Ack_Enable) || \
|
|
((STATE) == I2C_Ack_Disable))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_transfer_direction
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_Direction_Transmitter ((uint8_t)0x00)
|
|
#define I2C_Direction_Receiver ((uint8_t)0x01)
|
|
#define IS_I2C_DIRECTION(DIRECTION) (((DIRECTION) == I2C_Direction_Transmitter) || \
|
|
((DIRECTION) == I2C_Direction_Receiver))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_acknowledged_address
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_AcknowledgedAddress_7bit ((uint16_t)0x4000)
|
|
#define I2C_AcknowledgedAddress_10bit ((uint16_t)0xC000)
|
|
#define IS_I2C_ACKNOWLEDGE_ADDRESS(ADDRESS) (((ADDRESS) == I2C_AcknowledgedAddress_7bit) || \
|
|
((ADDRESS) == I2C_AcknowledgedAddress_10bit))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_registers
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_Register_CR1 ((uint8_t)0x00)
|
|
#define I2C_Register_CR2 ((uint8_t)0x04)
|
|
#define I2C_Register_OAR1 ((uint8_t)0x08)
|
|
#define I2C_Register_OAR2 ((uint8_t)0x0C)
|
|
#define I2C_Register_DR ((uint8_t)0x10)
|
|
#define I2C_Register_SR1 ((uint8_t)0x14)
|
|
#define I2C_Register_SR2 ((uint8_t)0x18)
|
|
#define I2C_Register_CCR ((uint8_t)0x1C)
|
|
#define I2C_Register_TRISE ((uint8_t)0x20)
|
|
#define IS_I2C_REGISTER(REGISTER) (((REGISTER) == I2C_Register_CR1) || \
|
|
((REGISTER) == I2C_Register_CR2) || \
|
|
((REGISTER) == I2C_Register_OAR1) || \
|
|
((REGISTER) == I2C_Register_OAR2) || \
|
|
((REGISTER) == I2C_Register_DR) || \
|
|
((REGISTER) == I2C_Register_SR1) || \
|
|
((REGISTER) == I2C_Register_SR2) || \
|
|
((REGISTER) == I2C_Register_CCR) || \
|
|
((REGISTER) == I2C_Register_TRISE))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_NACK_position
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_NACKPosition_Next ((uint16_t)0x0800)
|
|
#define I2C_NACKPosition_Current ((uint16_t)0xF7FF)
|
|
#define IS_I2C_NACK_POSITION(POSITION) (((POSITION) == I2C_NACKPosition_Next) || \
|
|
((POSITION) == I2C_NACKPosition_Current))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_SMBus_alert_pin_level
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_SMBusAlert_Low ((uint16_t)0x2000)
|
|
#define I2C_SMBusAlert_High ((uint16_t)0xDFFF)
|
|
#define IS_I2C_SMBUS_ALERT(ALERT) (((ALERT) == I2C_SMBusAlert_Low) || \
|
|
((ALERT) == I2C_SMBusAlert_High))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_PEC_position
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_PECPosition_Next ((uint16_t)0x0800)
|
|
#define I2C_PECPosition_Current ((uint16_t)0xF7FF)
|
|
#define IS_I2C_PEC_POSITION(POSITION) (((POSITION) == I2C_PECPosition_Next) || \
|
|
((POSITION) == I2C_PECPosition_Current))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_interrupts_definition
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_IT_BUF ((uint16_t)0x0400)
|
|
#define I2C_IT_EVT ((uint16_t)0x0200)
|
|
#define I2C_IT_ERR ((uint16_t)0x0100)
|
|
#define IS_I2C_CONFIG_IT(IT) ((((IT) & (uint16_t)0xF8FF) == 0x00) && ((IT) != 0x00))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_interrupts_definition
|
|
* @{
|
|
*/
|
|
|
|
#define I2C_IT_SMBALERT ((uint32_t)0x01008000)
|
|
#define I2C_IT_TIMEOUT ((uint32_t)0x01004000)
|
|
#define I2C_IT_PECERR ((uint32_t)0x01001000)
|
|
#define I2C_IT_OVR ((uint32_t)0x01000800)
|
|
#define I2C_IT_AF ((uint32_t)0x01000400)
|
|
#define I2C_IT_ARLO ((uint32_t)0x01000200)
|
|
#define I2C_IT_BERR ((uint32_t)0x01000100)
|
|
#define I2C_IT_TXE ((uint32_t)0x06000080)
|
|
#define I2C_IT_RXNE ((uint32_t)0x06000040)
|
|
#define I2C_IT_STOPF ((uint32_t)0x02000010)
|
|
#define I2C_IT_ADD10 ((uint32_t)0x02000008)
|
|
#define I2C_IT_BTF ((uint32_t)0x02000004)
|
|
#define I2C_IT_ADDR ((uint32_t)0x02000002)
|
|
#define I2C_IT_SB ((uint32_t)0x02000001)
|
|
|
|
#define IS_I2C_CLEAR_IT(IT) ((((IT) & (uint16_t)0x20FF) == 0x00) && ((IT) != (uint16_t)0x00))
|
|
|
|
#define IS_I2C_GET_IT(IT) (((IT) == I2C_IT_SMBALERT) || ((IT) == I2C_IT_TIMEOUT) || \
|
|
((IT) == I2C_IT_PECERR) || ((IT) == I2C_IT_OVR) || \
|
|
((IT) == I2C_IT_AF) || ((IT) == I2C_IT_ARLO) || \
|
|
((IT) == I2C_IT_BERR) || ((IT) == I2C_IT_TXE) || \
|
|
((IT) == I2C_IT_RXNE) || ((IT) == I2C_IT_STOPF) || \
|
|
((IT) == I2C_IT_ADD10) || ((IT) == I2C_IT_BTF) || \
|
|
((IT) == I2C_IT_ADDR) || ((IT) == I2C_IT_SB))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_flags_definition
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
* @brief SR2 register flags
|
|
*/
|
|
|
|
#define I2C_FLAG_DUALF ((uint32_t)0x00800000)
|
|
#define I2C_FLAG_SMBHOST ((uint32_t)0x00400000)
|
|
#define I2C_FLAG_SMBDEFAULT ((uint32_t)0x00200000)
|
|
#define I2C_FLAG_GENCALL ((uint32_t)0x00100000)
|
|
#define I2C_FLAG_TRA ((uint32_t)0x00040000)
|
|
#define I2C_FLAG_BUSY ((uint32_t)0x00020000)
|
|
#define I2C_FLAG_MSL ((uint32_t)0x00010000)
|
|
|
|
/**
|
|
* @brief SR1 register flags
|
|
*/
|
|
|
|
#define I2C_FLAG_SMBALERT ((uint32_t)0x10008000)
|
|
#define I2C_FLAG_TIMEOUT ((uint32_t)0x10004000)
|
|
#define I2C_FLAG_PECERR ((uint32_t)0x10001000)
|
|
#define I2C_FLAG_OVR ((uint32_t)0x10000800)
|
|
#define I2C_FLAG_AF ((uint32_t)0x10000400)
|
|
#define I2C_FLAG_ARLO ((uint32_t)0x10000200)
|
|
#define I2C_FLAG_BERR ((uint32_t)0x10000100)
|
|
#define I2C_FLAG_TXE ((uint32_t)0x10000080)
|
|
#define I2C_FLAG_RXNE ((uint32_t)0x10000040)
|
|
#define I2C_FLAG_STOPF ((uint32_t)0x10000010)
|
|
#define I2C_FLAG_ADD10 ((uint32_t)0x10000008)
|
|
#define I2C_FLAG_BTF ((uint32_t)0x10000004)
|
|
#define I2C_FLAG_ADDR ((uint32_t)0x10000002)
|
|
#define I2C_FLAG_SB ((uint32_t)0x10000001)
|
|
|
|
#define IS_I2C_CLEAR_FLAG(FLAG) ((((FLAG) & (uint16_t)0x20FF) == 0x00) && ((FLAG) != (uint16_t)0x00))
|
|
|
|
#define IS_I2C_GET_FLAG(FLAG) (((FLAG) == I2C_FLAG_DUALF) || ((FLAG) == I2C_FLAG_SMBHOST) || \
|
|
((FLAG) == I2C_FLAG_SMBDEFAULT) || ((FLAG) == I2C_FLAG_GENCALL) || \
|
|
((FLAG) == I2C_FLAG_TRA) || ((FLAG) == I2C_FLAG_BUSY) || \
|
|
((FLAG) == I2C_FLAG_MSL) || ((FLAG) == I2C_FLAG_SMBALERT) || \
|
|
((FLAG) == I2C_FLAG_TIMEOUT) || ((FLAG) == I2C_FLAG_PECERR) || \
|
|
((FLAG) == I2C_FLAG_OVR) || ((FLAG) == I2C_FLAG_AF) || \
|
|
((FLAG) == I2C_FLAG_ARLO) || ((FLAG) == I2C_FLAG_BERR) || \
|
|
((FLAG) == I2C_FLAG_TXE) || ((FLAG) == I2C_FLAG_RXNE) || \
|
|
((FLAG) == I2C_FLAG_STOPF) || ((FLAG) == I2C_FLAG_ADD10) || \
|
|
((FLAG) == I2C_FLAG_BTF) || ((FLAG) == I2C_FLAG_ADDR) || \
|
|
((FLAG) == I2C_FLAG_SB))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_Events
|
|
* @{
|
|
*/
|
|
|
|
/**
|
|
===============================================================================
|
|
I2C Master Events (Events grouped in order of communication)
|
|
===============================================================================
|
|
*/
|
|
|
|
/**
|
|
* @brief Communication start
|
|
*
|
|
* After sending the START condition (I2C_GenerateSTART() function) the master
|
|
* has to wait for this event. It means that the Start condition has been correctly
|
|
* released on the I2C bus (the bus is free, no other devices is communicating).
|
|
*
|
|
*/
|
|
/* --EV5 */
|
|
#define I2C_EVENT_MASTER_MODE_SELECT ((uint32_t)0x00030001) /* BUSY, MSL and SB flag */
|
|
|
|
/**
|
|
* @brief Address Acknowledge
|
|
*
|
|
* After checking on EV5 (start condition correctly released on the bus), the
|
|
* master sends the address of the slave(s) with which it will communicate
|
|
* (I2C_Send7bitAddress() function, it also determines the direction of the communication:
|
|
* Master transmitter or Receiver). Then the master has to wait that a slave acknowledges
|
|
* his address. If an acknowledge is sent on the bus, one of the following events will
|
|
* be set:
|
|
*
|
|
* 1) In case of Master Receiver (7-bit addressing): the I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED
|
|
* event is set.
|
|
*
|
|
* 2) In case of Master Transmitter (7-bit addressing): the I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED
|
|
* is set
|
|
*
|
|
* 3) In case of 10-Bit addressing mode, the master (just after generating the START
|
|
* and checking on EV5) has to send the header of 10-bit addressing mode (I2C_SendData()
|
|
* function). Then master should wait on EV9. It means that the 10-bit addressing
|
|
* header has been correctly sent on the bus. Then master should send the second part of
|
|
* the 10-bit address (LSB) using the function I2C_Send7bitAddress(). Then master
|
|
* should wait for event EV6.
|
|
*
|
|
*/
|
|
|
|
/* --EV6 */
|
|
#define I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED ((uint32_t)0x00070082) /* BUSY, MSL, ADDR, TXE and TRA flags */
|
|
#define I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED ((uint32_t)0x00030002) /* BUSY, MSL and ADDR flags */
|
|
/* --EV9 */
|
|
#define I2C_EVENT_MASTER_MODE_ADDRESS10 ((uint32_t)0x00030008) /* BUSY, MSL and ADD10 flags */
|
|
|
|
/**
|
|
* @brief Communication events
|
|
*
|
|
* If a communication is established (START condition generated and slave address
|
|
* acknowledged) then the master has to check on one of the following events for
|
|
* communication procedures:
|
|
*
|
|
* 1) Master Receiver mode: The master has to wait on the event EV7 then to read
|
|
* the data received from the slave (I2C_ReceiveData() function).
|
|
*
|
|
* 2) Master Transmitter mode: The master has to send data (I2C_SendData()
|
|
* function) then to wait on event EV8 or EV8_2.
|
|
* These two events are similar:
|
|
* - EV8 means that the data has been written in the data register and is
|
|
* being shifted out.
|
|
* - EV8_2 means that the data has been physically shifted out and output
|
|
* on the bus.
|
|
* In most cases, using EV8 is sufficient for the application.
|
|
* Using EV8_2 leads to a slower communication but ensure more reliable test.
|
|
* EV8_2 is also more suitable than EV8 for testing on the last data transmission
|
|
* (before Stop condition generation).
|
|
*
|
|
* @note In case the user software does not guarantee that this event EV7 is
|
|
* managed before the current byte end of transfer, then user may check on EV7
|
|
* and BTF flag at the same time (ie. (I2C_EVENT_MASTER_BYTE_RECEIVED | I2C_FLAG_BTF)).
|
|
* In this case the communication may be slower.
|
|
*
|
|
*/
|
|
|
|
/* Master RECEIVER mode -----------------------------*/
|
|
/* --EV7 */
|
|
#define I2C_EVENT_MASTER_BYTE_RECEIVED ((uint32_t)0x00030040) /* BUSY, MSL and RXNE flags */
|
|
|
|
/* Master TRANSMITTER mode --------------------------*/
|
|
/* --EV8 */
|
|
#define I2C_EVENT_MASTER_BYTE_TRANSMITTING ((uint32_t)0x00070080) /* TRA, BUSY, MSL, TXE flags */
|
|
/* --EV8_2 */
|
|
#define I2C_EVENT_MASTER_BYTE_TRANSMITTED ((uint32_t)0x00070084) /* TRA, BUSY, MSL, TXE and BTF flags */
|
|
|
|
|
|
/**
|
|
===============================================================================
|
|
I2C Slave Events (Events grouped in order of communication)
|
|
===============================================================================
|
|
*/
|
|
|
|
|
|
/**
|
|
* @brief Communication start events
|
|
*
|
|
* Wait on one of these events at the start of the communication. It means that
|
|
* the I2C peripheral detected a Start condition on the bus (generated by master
|
|
* device) followed by the peripheral address. The peripheral generates an ACK
|
|
* condition on the bus (if the acknowledge feature is enabled through function
|
|
* I2C_AcknowledgeConfig()) and the events listed above are set :
|
|
*
|
|
* 1) In normal case (only one address managed by the slave), when the address
|
|
* sent by the master matches the own address of the peripheral (configured by
|
|
* I2C_OwnAddress1 field) the I2C_EVENT_SLAVE_XXX_ADDRESS_MATCHED event is set
|
|
* (where XXX could be TRANSMITTER or RECEIVER).
|
|
*
|
|
* 2) In case the address sent by the master matches the second address of the
|
|
* peripheral (configured by the function I2C_OwnAddress2Config() and enabled
|
|
* by the function I2C_DualAddressCmd()) the events I2C_EVENT_SLAVE_XXX_SECONDADDRESS_MATCHED
|
|
* (where XXX could be TRANSMITTER or RECEIVER) are set.
|
|
*
|
|
* 3) In case the address sent by the master is General Call (address 0x00) and
|
|
* if the General Call is enabled for the peripheral (using function I2C_GeneralCallCmd())
|
|
* the following event is set I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED.
|
|
*
|
|
*/
|
|
|
|
/* --EV1 (all the events below are variants of EV1) */
|
|
/* 1) Case of One Single Address managed by the slave */
|
|
#define I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED ((uint32_t)0x00020002) /* BUSY and ADDR flags */
|
|
#define I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED ((uint32_t)0x00060082) /* TRA, BUSY, TXE and ADDR flags */
|
|
|
|
/* 2) Case of Dual address managed by the slave */
|
|
#define I2C_EVENT_SLAVE_RECEIVER_SECONDADDRESS_MATCHED ((uint32_t)0x00820000) /* DUALF and BUSY flags */
|
|
#define I2C_EVENT_SLAVE_TRANSMITTER_SECONDADDRESS_MATCHED ((uint32_t)0x00860080) /* DUALF, TRA, BUSY and TXE flags */
|
|
|
|
/* 3) Case of General Call enabled for the slave */
|
|
#define I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED ((uint32_t)0x00120000) /* GENCALL and BUSY flags */
|
|
|
|
/**
|
|
* @brief Communication events
|
|
*
|
|
* Wait on one of these events when EV1 has already been checked and:
|
|
*
|
|
* - Slave RECEIVER mode:
|
|
* - EV2: When the application is expecting a data byte to be received.
|
|
* - EV4: When the application is expecting the end of the communication: master
|
|
* sends a stop condition and data transmission is stopped.
|
|
*
|
|
* - Slave Transmitter mode:
|
|
* - EV3: When a byte has been transmitted by the slave and the application is expecting
|
|
* the end of the byte transmission. The two events I2C_EVENT_SLAVE_BYTE_TRANSMITTED and
|
|
* I2C_EVENT_SLAVE_BYTE_TRANSMITTING are similar. The second one can optionally be
|
|
* used when the user software doesn't guarantee the EV3 is managed before the
|
|
* current byte end of transfer.
|
|
* - EV3_2: When the master sends a NACK in order to tell slave that data transmission
|
|
* shall end (before sending the STOP condition). In this case slave has to stop sending
|
|
* data bytes and expect a Stop condition on the bus.
|
|
*
|
|
* @note In case the user software does not guarantee that the event EV2 is
|
|
* managed before the current byte end of transfer, then user may check on EV2
|
|
* and BTF flag at the same time (ie. (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_BTF)).
|
|
* In this case the communication may be slower.
|
|
*
|
|
*/
|
|
|
|
/* Slave RECEIVER mode --------------------------*/
|
|
/* --EV2 */
|
|
#define I2C_EVENT_SLAVE_BYTE_RECEIVED ((uint32_t)0x00020040) /* BUSY and RXNE flags */
|
|
/* --EV4 */
|
|
#define I2C_EVENT_SLAVE_STOP_DETECTED ((uint32_t)0x00000010) /* STOPF flag */
|
|
|
|
/* Slave TRANSMITTER mode -----------------------*/
|
|
/* --EV3 */
|
|
#define I2C_EVENT_SLAVE_BYTE_TRANSMITTED ((uint32_t)0x00060084) /* TRA, BUSY, TXE and BTF flags */
|
|
#define I2C_EVENT_SLAVE_BYTE_TRANSMITTING ((uint32_t)0x00060080) /* TRA, BUSY and TXE flags */
|
|
/* --EV3_2 */
|
|
#define I2C_EVENT_SLAVE_ACK_FAILURE ((uint32_t)0x00000400) /* AF flag */
|
|
|
|
/*
|
|
===============================================================================
|
|
End of Events Description
|
|
===============================================================================
|
|
*/
|
|
|
|
#define IS_I2C_EVENT(EVENT) (((EVENT) == I2C_EVENT_SLAVE_TRANSMITTER_ADDRESS_MATCHED) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_RECEIVER_ADDRESS_MATCHED) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_TRANSMITTER_SECONDADDRESS_MATCHED) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_RECEIVER_SECONDADDRESS_MATCHED) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_GENERALCALLADDRESS_MATCHED) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_BYTE_RECEIVED) || \
|
|
((EVENT) == (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_DUALF)) || \
|
|
((EVENT) == (I2C_EVENT_SLAVE_BYTE_RECEIVED | I2C_FLAG_GENCALL)) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_BYTE_TRANSMITTED) || \
|
|
((EVENT) == (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_DUALF)) || \
|
|
((EVENT) == (I2C_EVENT_SLAVE_BYTE_TRANSMITTED | I2C_FLAG_GENCALL)) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_STOP_DETECTED) || \
|
|
((EVENT) == I2C_EVENT_MASTER_MODE_SELECT) || \
|
|
((EVENT) == I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED) || \
|
|
((EVENT) == I2C_EVENT_MASTER_RECEIVER_MODE_SELECTED) || \
|
|
((EVENT) == I2C_EVENT_MASTER_BYTE_RECEIVED) || \
|
|
((EVENT) == I2C_EVENT_MASTER_BYTE_TRANSMITTED) || \
|
|
((EVENT) == I2C_EVENT_MASTER_BYTE_TRANSMITTING) || \
|
|
((EVENT) == I2C_EVENT_MASTER_MODE_ADDRESS10) || \
|
|
((EVENT) == I2C_EVENT_SLAVE_ACK_FAILURE))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_own_address1
|
|
* @{
|
|
*/
|
|
|
|
#define IS_I2C_OWN_ADDRESS1(ADDRESS1) ((ADDRESS1) <= 0x3FF)
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/** @defgroup I2C_clock_speed
|
|
* @{
|
|
*/
|
|
|
|
#define IS_I2C_CLOCK_SPEED(SPEED) (((SPEED) >= 0x1) && ((SPEED) <= 400000))
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/* Exported macro ------------------------------------------------------------*/
|
|
/* Exported functions --------------------------------------------------------*/
|
|
|
|
/* Function used to set the I2C configuration to the default reset state *****/
|
|
void I2C_DeInit(I2C_TypeDef* I2Cx);
|
|
|
|
/* Initialization and Configuration functions *********************************/
|
|
void I2C_Init(I2C_TypeDef* I2Cx, I2C_InitTypeDef* I2C_InitStruct);
|
|
void I2C_StructInit(I2C_InitTypeDef* I2C_InitStruct);
|
|
void I2C_Cmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_DigitalFilterConfig(I2C_TypeDef* I2Cx, uint16_t I2C_DigitalFilter);
|
|
void I2C_AnalogFilterCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_GenerateSTART(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_GenerateSTOP(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_Send7bitAddress(I2C_TypeDef* I2Cx, uint8_t Address, uint8_t I2C_Direction);
|
|
void I2C_AcknowledgeConfig(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_OwnAddress2Config(I2C_TypeDef* I2Cx, uint8_t Address);
|
|
void I2C_DualAddressCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_GeneralCallCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_SoftwareResetCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_StretchClockCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_FastModeDutyCycleConfig(I2C_TypeDef* I2Cx, uint16_t I2C_DutyCycle);
|
|
void I2C_NACKPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_NACKPosition);
|
|
void I2C_SMBusAlertConfig(I2C_TypeDef* I2Cx, uint16_t I2C_SMBusAlert);
|
|
void I2C_ARPCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
|
|
/* Data transfers functions ***************************************************/
|
|
void I2C_SendData(I2C_TypeDef* I2Cx, uint8_t Data);
|
|
uint8_t I2C_ReceiveData(I2C_TypeDef* I2Cx);
|
|
|
|
/* PEC management functions ***************************************************/
|
|
void I2C_TransmitPEC(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_PECPositionConfig(I2C_TypeDef* I2Cx, uint16_t I2C_PECPosition);
|
|
void I2C_CalculatePEC(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
uint8_t I2C_GetPEC(I2C_TypeDef* I2Cx);
|
|
|
|
/* DMA transfers management functions *****************************************/
|
|
void I2C_DMACmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
void I2C_DMALastTransferCmd(I2C_TypeDef* I2Cx, FunctionalState NewState);
|
|
|
|
/* Interrupts, events and flags management functions **************************/
|
|
uint16_t I2C_ReadRegister(I2C_TypeDef* I2Cx, uint8_t I2C_Register);
|
|
void I2C_ITConfig(I2C_TypeDef* I2Cx, uint16_t I2C_IT, FunctionalState NewState);
|
|
|
|
/*
|
|
===============================================================================
|
|
I2C State Monitoring Functions
|
|
===============================================================================
|
|
This I2C driver provides three different ways for I2C state monitoring
|
|
depending on the application requirements and constraints:
|
|
|
|
|
|
1. Basic state monitoring (Using I2C_CheckEvent() function)
|
|
-----------------------------------------------------------
|
|
It compares the status registers (SR1 and SR2) content to a given event
|
|
(can be the combination of one or more flags).
|
|
It returns SUCCESS if the current status includes the given flags
|
|
and returns ERROR if one or more flags are missing in the current status.
|
|
|
|
- When to use
|
|
- This function is suitable for most applications as well as for startup
|
|
activity since the events are fully described in the product reference
|
|
manual (RM0090).
|
|
- It is also suitable for users who need to define their own events.
|
|
|
|
- Limitations
|
|
- If an error occurs (ie. error flags are set besides to the monitored
|
|
flags), the I2C_CheckEvent() function may return SUCCESS despite
|
|
the communication hold or corrupted real state.
|
|
In this case, it is advised to use error interrupts to monitor
|
|
the error events and handle them in the interrupt IRQ handler.
|
|
|
|
Note
|
|
For error management, it is advised to use the following functions:
|
|
- I2C_ITConfig() to configure and enable the error interrupts (I2C_IT_ERR).
|
|
- I2Cx_ER_IRQHandler() which is called when the error interrupt occurs.
|
|
Where x is the peripheral instance (I2C1, I2C2 ...)
|
|
- I2C_GetFlagStatus() or I2C_GetITStatus() to be called into the
|
|
I2Cx_ER_IRQHandler() function in order to determine which error occurred.
|
|
- I2C_ClearFlag() or I2C_ClearITPendingBit() and/or I2C_SoftwareResetCmd()
|
|
and/or I2C_GenerateStop() in order to clear the error flag and source
|
|
and return to correct communication status.
|
|
|
|
|
|
2. Advanced state monitoring (Using the function I2C_GetLastEvent())
|
|
--------------------------------------------------------------------
|
|
Using the function I2C_GetLastEvent() which returns the image of both status
|
|
registers in a single word (uint32_t) (Status Register 2 value is shifted left
|
|
by 16 bits and concatenated to Status Register 1).
|
|
|
|
- When to use
|
|
- This function is suitable for the same applications above but it
|
|
allows to overcome the mentioned limitation of I2C_GetFlagStatus()
|
|
function.
|
|
- The returned value could be compared to events already defined in
|
|
this file or to custom values defined by user.
|
|
This function is suitable when multiple flags are monitored at the
|
|
same time.
|
|
- At the opposite of I2C_CheckEvent() function, this function allows
|
|
user to choose when an event is accepted (when all events flags are
|
|
set and no other flags are set or just when the needed flags are set
|
|
like I2C_CheckEvent() function.
|
|
|
|
- Limitations
|
|
- User may need to define his own events.
|
|
- Same remark concerning the error management is applicable for this
|
|
function if user decides to check only regular communication flags
|
|
(and ignores error flags).
|
|
|
|
|
|
3. Flag-based state monitoring (Using the function I2C_GetFlagStatus())
|
|
-----------------------------------------------------------------------
|
|
|
|
Using the function I2C_GetFlagStatus() which simply returns the status of
|
|
one single flag (ie. I2C_FLAG_RXNE ...).
|
|
|
|
- When to use
|
|
- This function could be used for specific applications or in debug
|
|
phase.
|
|
- It is suitable when only one flag checking is needed (most I2C
|
|
events are monitored through multiple flags).
|
|
- Limitations:
|
|
- When calling this function, the Status register is accessed.
|
|
Some flags are cleared when the status register is accessed.
|
|
So checking the status of one Flag, may clear other ones.
|
|
- Function may need to be called twice or more in order to monitor
|
|
one single event.
|
|
*/
|
|
|
|
/*
|
|
===============================================================================
|
|
1. Basic state monitoring
|
|
===============================================================================
|
|
*/
|
|
ErrorStatus I2C_CheckEvent(I2C_TypeDef* I2Cx, uint32_t I2C_EVENT);
|
|
/*
|
|
===============================================================================
|
|
2. Advanced state monitoring
|
|
===============================================================================
|
|
*/
|
|
uint32_t I2C_GetLastEvent(I2C_TypeDef* I2Cx);
|
|
/*
|
|
===============================================================================
|
|
3. Flag-based state monitoring
|
|
===============================================================================
|
|
*/
|
|
FlagStatus I2C_GetFlagStatus(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG);
|
|
|
|
|
|
void I2C_ClearFlag(I2C_TypeDef* I2Cx, uint32_t I2C_FLAG);
|
|
ITStatus I2C_GetITStatus(I2C_TypeDef* I2Cx, uint32_t I2C_IT);
|
|
void I2C_ClearITPendingBit(I2C_TypeDef* I2Cx, uint32_t I2C_IT);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /*__STM32F4xx_I2C_H */
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/**
|
|
* @}
|
|
*/
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|